ARDUINO RGB LED TEST HOW TO
ARDUINO RGB LED TEST DRIVER
ARDUINO RGB LED TEST CODE

ARDUINO RGB LED TEST DRIVER

Reverse biased voltage protection that is the driver IC is not damaged even if the power supply is connected in reverse.Some of the cool features of WS2812B are : Input signal voltage : -0.5 to VDD+0.5Volts.Power supply voltage(VDD) : +3.5 to +5.3Volts.WS2812B RBG LED Features and Specifications With this value we will be able to choose the corresponding color for the RGB LED.The pin configuration details are listed below in the tabular form: Number Note: in programming we usually start to count from 0, not 1. īecause we want to choose between 7 different options, we use the map() function to transform this value from the range 0-1023 to the range 0-6. In the void loop(), we first read the potentiometer’s value with analogRead(). Read potentiometer and choose a mode void loop() By calling this function, instead of 3 redundant lines, you just have one line, which is digitalWriteRGB() with 3 parameters.

ARDUINO RGB LED TEST CODE

This function will help us reduce the code we write in the following.Įvery time you need to change the color of the RGB LED, you will need to call digitalWrite() 3 times. digitalWriteRGB() function void digitalWriteRGB(byte red, byte blue, byte green) Nothing to do for the potentiometer, as an analog pin is already in input mode by default. In the void setup(), we initialize all LEDs (in fact, the 3 legs of the RGB LED) to OUTPUT mode. One for the potentiometer, and one for each color of the LED – we write the code as if we were controlling 3 different LEDs. Setup RGB and potentiometer pins #define RGB_RED_PIN 11Īt first, as a best practice, we create a define for each pin we are going to use. Int mode = map(potentiometerValue, 0, 1023, 0, 6) Int potentiometerValue = analogRead(POTENTIOMETER_PIN)

Void digitalWriteRGB(byte red, byte blue, byte green) We are going to use digitalWrite() – LED fully powered on/off, which means that we have a combination of 7 colors: You can see the RGB LED as a combination of 3 different LEDs that you control separately. In this first application, we are going to modify the color of the RGB LED when we turn the potentiometer knob.

Connect the middle leg to an analog pin.Ĭontrol the RGB LED with the potentiometer – digitalWrite() – 7 colors.

The other extreme leg should be connected to 5V on the Arduino.

Connect one of the extreme leg (for example left) to the ground.

Add a 220 Ohm resistor in between for each leg. Connect each of these legs to a PWM compatible digital pin on the Arduino (with a “~” next to the number, like on the picture).

The 3 other legs correspond to red, blue, and green colors.

If it’s an anode, plug it to 5V on the Arduino. So, if it’s a cathode, plug this to the ground (GND). If no instructions, you can first try the “cathode mode” and see if it works.

ARDUINO RGB LED TEST HOW TO

How to find out? Simply check the manual or description of what you’ve bought. Depending on your RGB LED, this can be a cathode or an anode. Make a common ground by connecting a GND pin of the Arduino, to the “minus” line of the breadboard.You are learning how to use Arduino to build your own projects?Ĭheck out Arduino For Beginners and learn step by step. Arduino board – I use Arduino Uno, but any board where you have at least 3 PWM compatible digital pins, and one analog pin, is fine.Going further with the potentiometer and RGB LEDĪrduino circuit with RGB LED and potentiometer.Select a different color for each value.Control the RGB LED with potentiometer – analogWrite() – 1536 colors.Power on the RGB LED depending on the potentiometer’s value.Control the RGB LED with the potentiometer – digitalWrite() – 7 colors.Arduino circuit with RGB LED and potentiometer.

Arduino rgb led test